Multiboard Street Deck Kit
The Multiboard Kits include our Canadian hard maple veneer, the key to making premium quality, long lasting decks. With this kit, you control the laminating process, using waterproof glue, the best skateboard veneer in the world and thousands of pounds of pressure. Make it right. Make it yourself!
Select from 9 different shapes using pre-engraved templates on each veneer!
Ghost Rockit (Mini-Cruiser): Length - 22 1/2” / Width - 8 1/2” / Wheelbase - 13 1/2”
Lil’Rockit (Mini-Cruiser): Length - 22 3/4” / Width - 6 1/4” / Wheelbase - 12”
Lil’Pintail (Cruiser): Length - 27” / Width - 8” / Wheelbase - 15 1/2”
Lil’Fish (Cruiser): Length - 27” / Width - 8 1/2” / Wheelbase - 15 1/4”
Big’Rockit (Cruiser): Length - 29” / Width - 7 1/2” / Wheelbase - 14 1/2”
Bottle Rockit (Double-Kick): Length - 30 3/4” / Width - 8” / Wheelbase - 15”
Street Deck 7 7/8 (Double-Kick): Length - 31 1/2” / Width - 7 7/8” / Wheelbase - 13 3/4”
Street Deck 8.5 (Double-Kick): Length - 32 1/4” / Width - 8 1/2” / Wheelbase - 13 3/4”
Old School (Double-Kick): Length - 32” / Width - 9 1/4” / Wheelbase - 14 1/4”
(approximate sizes, wheels and trucks are not included)
Multiboard Street Deck Kit contains:
- 7-layers of Canadian maple per board
- includes 5 pre-engraved template sheets (9 possible shapes), and 2 cross grain sheets per board
- 3-dimensionally shaped foam mold
- glue, roller and measuring cup
- edging tool and sandpaper
- illustrated instructions
and a Thin Air Press Kit
- 20 x 70” heavy duty vinyl vacuum bag with one-way valve attached
- manual vacuum Super Pump
- breather netting
- extra sealing tape
By following the printed instructions included in the kit box, you will be guided through the glue up, stacking on the mold, inserting and sealing into the TAP bag. Using the manual vacuum pump to evacuate the air, the Thin Air Press will press the veneers over the mold. The sanding process is described, as well as some graphics suggestions.
If you choose to set this up for riding, select grip tape on this page. Shop locally for your hardware (wheels, trucks and bearings). Use the guide holes on the bottom side to drill the truck holes through, using a 3/16” drill bit. And of course, don’t forget to wear your helmet!
The foam mold, Thin Air Press Bag and pump, edging tool and breather netting are designed to be used for many, many builds.
Keep all your reusable kit parts in good working order by following the maintenance tips included with the kit.
Q: Is this kit reusable?
A: Yes. Every thing but the veneer and glue are reusable
Q: What if my TAP bag or valve is leaking?
A: 99.9% of the time, the seal is not closed up properly. Dust and debris can prevent the top cap of the valve to seal, rinse cap with water. For more in-depth details, see the TAP kit FAQ’s page.
Q: Can I get more veneer?
A: A Refill for this kit is available here
Q: Can I change the template shapes? A: You can easily use the template shapes as a base and make changes to customize it to your liking. The pre-engraved template lines can be sanded away or easily covered with graphics or grip tape.
Q: Will stuff last if I don’t use it right away?
A: Veneer will absorb and lose moisture, so keep it sealed in plastic (or the carton it arrived in) but away from any heat sources. Lay it flat to prevent warping. Prevent the glue from freezing.
Q: What do I do if my veneer breaks or splits?
A: Veneer is fragile until laminated, and it is common to split or snap (especially the cross grains). A stripe of glue and some masking tape to hold it until it dries will fix broken or split sheets. See video how-to-fix
Q: How do I get this cheaper?
A: Become an entrepreneur! Each kit allows you to make more than one deck, build one for yourself and generate income from the other boards you build!
Q: What else do I need to complete this project?
A: A moisture protector is recommended (sponge on water-based outdoor clear coat) to seal all surfaces, especially your edges and before applying any graphics.